bin eben erst back, aber nice zu sehen das der Mod auf anderen Karten Fortschritte macht"!

Meine Erfolgsmeldung war ggf. ein wenig voreinlig :-(

Der selber funktionierte tatsächlich. Aber bei 3D Anwendungen oder 3D Renderer (ATI Tray Tool) bekomme ich recht schnell nen Blackscreen und PC muss neu gebootet werden....

Komischerweise passiert das (mit dem MOD) auch wenn ich den GPU-Takt wieder so einstelle wie er ohne Mod funktionierte....

Ist das die besagte Over Volt Protection? Diesen blöden R3066 bekomme ich nicht richtig auf 6 Ohm... Mit Bleistift ist er immer äußerst am schwanken.

Durch das viel Bleistiften und wegmachen (denke daran liegt es) habe ich jetzt sogar auf dem R3066 11,5 ohm (original 10,8 oder 10,9 Ohm) -> hierdurch habe ich jetzt im Nichtgemoddeten zustand VGPU 1,25 (original 1,24).... Hatte davon ja auch gehört das der R3066 auch die Spannung "regelt"...

Alles sehr strange... Hat einer ne Lösung oder nen Hinweis wie ich den R3066 richtig auf 6 Ohm bekomme?

besten dank.

einen poti anlöten?

Habe noch was vergessen:

Habe Catalyst 7.7 drauf. Kann es am Treiber liegen?????

Hi,
I'm doing vmod with pencil.I want to know,where is the problem.When i'm paint on this ,and do 1.37Voltage,i turning on a pc,and a sound goes from motherboard..It's like a long beep(about 1s),and short one(about 0.5s)..
Where is a problem?
Thanks
P.S.Sorry for bad English :{ I think,you understand me

Hallo,

your english ok...

do you try to remove the vmod and boot the pc? What Card do you have? it possible that the change dont work because there are some diffrent Versions of the X1950 out. Can you shoot some Pics of your back card?

MFG

Now i'm sitting on "fresh" pc non oc'ed vga When i clean that place,computer is started normaly
I have ASUS EAX1950PRO 256mb.
I can shot a few foto's,but of your fotos,i think,i have ident card as yours.

So then it should work. Have you used the right pencil?

My vga's foto with horible quality
And this is my Pencil

Do you have a "multi meter" at home? Or can you check the Voltage manually?

There is problem.I don't have any devices,with who i can measure voltage :||
I use RivaTuner hardware monitoring My temp. is ~40C idle,~67burn(low rpm)
P.S.Maybe i made a mistake in my previous post.Everythink was that:
when i colored the transistor to reduce the resistivity and tried to turn on the computer, i heard it beeping 2 times, first time it beeped for a second, and 2nd time it beeped for 0.5~ second, but i guess it was booting up since i could hear my vga cooler spining at max RPMs because it sounded awfull, and i could hear my HDD Spining, but the monitor just didint turn on.But windows is booting up.

one quaestion: on wich place do you use the Pencil?

because we found out that its not important to pencil the Resistor. It only must work when you uses your solvercompound to take the bridges between resistor group for voltage regulation

Zitat von invalid

one quaestion: on wich place do you use the Pencil?

because we found out that its not important to pencil the Resistor. It only must work when you uses your solvercompound to take the bridges between resistor group for voltage regulation

I use Pencil to paint resistor,to reduce the resistivity.I'm brushed whole resistor ;]
So,you say,i need just silver conductive paint ?
1 stupid question,silver conductive paint is not the same as Thermal gease?

no, it is not the same.

the pencil you need only for the R3066 Resistor. for the other resistors you nedd Silver conductive

R3066 resistor is this one?
There is my problem When i paint this resistor,my pc is beeping